New Year Energy Drink Carrier

Hi Everyone

First, I would like to thank each and every one of you who took time from your busy days to watch my videos or visit the website.  I am humbled and overjoyed that we can spend some time sharing this love of creating that we all enjoy.

Second, I wanted to let you know that I am going to take a couple of weeks off to visit my Mom with the kids.  I will also reorganize my craft space, so we can be ready to create in the New Year!

On to today’s project, which is an adorable energy drink carrier.  Modeled after some of the cup carriers, I sized this one to fit some of the energy drinks that are available on the market, but any similar sized product would work.  With all of the New Year’s celebrations and parties, perhaps you know someone who would benefit from a little energy boost.  (Someone  mentioned it may fit the little wine or liquor bottles, and if anyone has one around, please let me know!  I’m thinking it may need to be a little taller, so your 6 3/4″ measurement may need to be increased if you wish to give spirits, instead.)

Start with a 6 3/4″ by 11″ piece of card stock, and score with the short side up at 1 3/4″ and 3 3/4″.  Turn the card stock with the long side up, but make sure that the smaller (1 3/4″) section is at the bottom, and the larger (3″ for this size) section is at the top.  (This is because we will do some partial scoring.)  Score all the way at 1 3/4″, 5 1/4″, 7″, and 10 1/2″.  Then score JUST TO THE FIRST SCORE LINE at 3 1/2″ and 8 3/4″.  Fold and burnish all the complete score lines, but don’t worry about the two partial ones at this point.

Cut the top and bottom sections of the 1/2″ glue tab, leaving only the middle section in place.  In landscape, with the 1 3/4″ section down, cut up along the scorelines on the rectangles and slightly notch into the squares, as this will be the bottom of the box.  On the top, I cut carefully down each side of the score line, to the first intersecting scoreline, for each of the full length scores. Then just snipped the score line off.  (Don’t cut the partial scorelines, yet.)  For the two narrow sections, they will fold down, so I trimmed them just shorter than the side of the box.

On the sections with the partial score, cut the side and score line free from the box that is opposite the side of the box with the glue tab.  This will give you two sections where half of the section swings free like a door.  (The video is much better than words.)  It has to be done on the same side of both partial scores, because we will need to swing them in and glue them together to form the handle.  Before that happens, we need to glue the bottom of the box together as normal, side tabs, then back tab, then front.  Now is the time to swing in and glue the two flaps together to form the handle, and slide a 1″ circle punch down on that section to punch a finger hole.

Wrap and adhere a 1 3/4″ by 11″ piece of patterned paper around the box, lining up the edge with the seam of the box.  Stamp a sentiment and punch with the Pretty Label Punch.  I used a mat made from another Pretty Label punch cut in half vertically, and offset slightly on each end.  It gives the illusion of having a slightly larger mat.  Then, stick it on with foam tape, and add an embellishment to complete!  Stick your offerings in, and gift!

If you use a patterned card stock, you may not need to wrap it will paper and can just stick a sentiment on and be good to go.  Either way, it makes a nice gift for anyone to celebrate the New Year.

Thank you for stopping by, and I will be back in a couple of weeks.  However you celebrate, I pray it is safe and joyful.  So, until we meet again, may your days be blessed.  ~Darby

  • Supplies:
  • Card stock:  Stampin’ Up! Very Vanilla, Calypso Coral, Whisper White, Gold Foil, Old Olive.
  • Paper:  Stampin’ Up! Year of Cheer, Whole Lot of Lovely
  • Stamps:  Stampin’ Up! Merry Cafe
  • Punches:  Stampin’ Up! Pretty Label Punch, Star Punch (retired)

Christmas 2017 Teapot Treat and Gift Card Holder

Hi Everyone,

The last project for this Christmas is an all-purpose, treat, teabag or gift card holder.  In the shape of a teapot, it is an adorable way to give someone a treat and a gift card.  Dress it up for Christmas, or decorate it to personalize it to your recipient.

The pocket on the teapot measures 3″ by 3 3/4″ by 1/2″, and will fit a couple of teabags, a gift card, some candy or even small pieces of jewelry.  It is made from an 8″ by 8″ piece of card stock, and scored on the diagonal.

Place the diagonal on the 1/4″ in line and score, turn the piece 180 degrees, and place the diagonal on the 1/4″ line and score again.  This will give you a 1/2″ strip down the center of the diagonal.  Turn it 90 degrees, and now place the diagonal on the 1 1/2″ line and score, turn it 180 degrees and place the diagonal on the 1 1/2″ line and score again.

I used a 1 1/2″ punch to round the corners at the top and on both flaps for the handle.  I used a 1″ circle punch to create the handle, and also to shape the curve in the spout.  It is not hard to create, but a bit hard to explain.  So, I will put in the video so you can watch how I did it.

This project finishes the Christmas 2017 series, and I hope you enjoyed these projects as much as I did bringing them to you.

I want to wish all of you a very Merry Christmas, and may you find joy and peace in the child of Bethlehem.  Rejoice!  ~Darby

 

 

Christmas 2017 Special Delivery Lindt Reindeer

Hi Everyone,

I have an adorable, and delicious, little reindeer treat holder for you today.  It is a Special Delivery crate, straight from the North Pole, that contains a wonderful, and tasty, chocolate Lindt Reindeer.

Start with a 6 1/2″ by 8 1/2″ piece of card stock.  Score with the 6 1/2″ side up at 2 1/2″ and 4″.  Score with the 8 1/2″ side up at 2 1/2″ and 6″.  With the piece in landscape  (horizontal) position, cut neatly up the score lines on both sides of the rectangle in the center, and notch into the corner squares to make the assembly neater.  Turn the piece around and do the same thing to the other side.

Turn the shorter end towards you, the 1 1/2″ section in the middle will be the front or back, so you only need about 1/2″ on the outside of the score lines for glue tabs.  So, you will be cutting away a lot of the outside corners.  Turn the piece around until the other end is facing you and do the same thing.  See the video below for a visual guide.

On one of the narrow ends (which will become the front) take a 1 1/2″ circle punch or scissors, and create a “scooped” area where the neck of the reindeer will sit.   Decide which side you wish to have the sentiment on, and on the other side, use the Classic Label Punch to make two slots in the side.  I made mine at 1″ and 1 3/4″ from the bottom score line.   Then glue the tabs to the sides and create the crate.

Use two circle tab punchies to glue over the sides of the crate with a strong adhesive (I used liquid glue), and punch a 1/4″ hole in the circle.  Thread a ribbon through, and secure on itself using a strong double-sided tape adhesive.  I put the tabs slightly to the front of center, because the reindeer is a little heavier toward the head.  Then, make a bow for each side and glue on with glue dots.  I used the Quilted Christmas ribbon.

Stamp the sentiment from the Merry Little Labels stamp set in cherry cobbler onto whisper white card stock, and cut using the second largest stitched shape oval.  Cut a coordinating scalloped oval from the layering ovals, and glue the sentiment to it.  Then, glue this onto the side of the crate that has not been cut out.  Add the reindeer, and give to young or old!

I had a though after creating the video, that a “name tag” around the neck of the reindeer and hanging over the front of the crate, would be an adorable place to write the “to-from” for the gift.  Some small jingle bells would be pretty cute, too!

I hope you enjoy this cute little project, and give it a try.

And, until we meet again, I hope your days are blessed!  ~Darby

 

 

Christmas 2017 Ribbon Bookmarks Ready for Gifting

Hi Everyone,

Please don’t object to my use of “gifting” for this project.  I wanted to convey a sense of giving, but have it include all of the warm and wonderful thoughts and feelings that go into creating a present personalized just for the person receiving the gift.

Ribbon Bookmarks packaged and ready for giving

These bookmarks can be made with what you already have in your stash, but can still be beautifully personalized to the person receiving the gift.  They can be a thoughtful gift by themselves, as stocking stuffer, or can accompany a carefully and lovingly selected book.

The bookmarks are made with a 9″ length of ribbon, although the length can be adjusted if you are giving them with a taller book.  I used the Circle Tab Punch for each end of the bookmark, so the width of your ribbon can vary from 1/2″ to 1″, which is just smaller than the width of the “shoulders” of the circle tab punch.  You probably want to select a ribbon that is not bulky, because it will be sandwiched between the circle tab punch layers.

The most important thing to watch out for is the glue.  Take time to glue the bookmark carefully, as you don’t want any stray glue to stick to the pages of the book.  I used a touch of Fast Fuse to stick it fast, but a bit of Tombow to hold for the long run.  You can personalize these any way you wish using different ribbons, card stock colors, stamped images and even tassels.  If using premade tassels, make sure to carefully “twist” the jump ring open and closed to keep it round.  Watch the video for a visual explanation.

I packaged them in a 2″ x 8″ cellophane bag, and used a strip of card stock 10″ by 1 7/8″, scored at 8″, with the scored end punched in the Scalloped Tag Topper punch.  Stamp a sentiment on this top flap.  Next, cut a slit in the card stock about 3″ from the bottom, and centered 1/2″ from each side.  That is where I pulled the bulk of the ribbon through so the bookmark top and bottom would be visible in the packaging. If you have repositionable adhesive, you could stick it down with that.  I used some washi tape from the Year of Cheer to hold it in place, because the washi doesn’t usually leave any stickiness or residual. Test yours to be sure. Remember to secure the ribbon on the back as well.  Then slip the card stock and bookmark into the cello bag, fold over the top flap and stick with a glue dot to the cellophane bag, thread a ribbon or twine through and around, and tie a knot or bow.  Embellish as desired.

Here are the ones I created:

A more masculine version, this was made with the Night of Navy Crinkled ribbon, tab punches from Whisper White and stamped with Touches of Texture in Sahara Sand, and embellished with the rooster and “for you” from the Wood Words stamp set.  The 3/4″ circle punch cuts sentiments and images that fit well in the circle tab punch.  The sentiment is from SU Christmas Pines.  I used a snowflake punch from The Paper Studio.

The next one was made with Berry Burst finely woven ribbon, gold foil paper tabs, gold embossed flower from Better Together, gold embossed “enjoy” from Tabs for Everything, package embellishment with the Holly Berry builder punchies, and sentiment stamped in berry burst from the Better Together stamp set.  Gold tassel from the Eastern Beauty collection.

The third one was created from the Fresh Fig finely woven ribbon, gold foil paper tabs, “Hello” and flower image from Easter Beauty stamp set, fresh fig tassel from the same collection, gold foil and silver glimmer paper punched stars (SU retired punch) and fresh fig stamped sentiment from Better Together.

I hope you enjoy this project, and find it useful for your Christmas giving.

And, until we meet again, may your days be blessed!  ~Darby

 

Christmas 2017 Everyday Label Punch Treat box & Ornament

Hi Everyone,

What a fun treat box that you can hang on the Christmas Tree as an ornament, or place on the table for a festive treat holder and place card.  Because of the coordinating stamps and punch, this goes very quickly, and can use up many of the scraps you cut off to make other projects.  It looks great in many different color combinations, whether traditional Christmas red and green, or perhaps a unique lemon-lime and berry burst.

Scroll down for video tutorial

The little boxes will fit 3 Rolos, or 3 Hershey’s kisses (especially the Candy Kisses which are out now and oh so yummy!) Or, it will fit 2-3 starlight mints, and you can make some with the sugar-free version for your local nursing home residents.

All you need is enough card stock for two Everyday Label punchies, I used the whisper white, but you may use whatever color coordinates with your event.  The “box” part is made from one 2″ by 6 3/4″ strip of card stock.  It is scored the same way for either the vertically oriented image or the horizontally oriented image.  The only difference between the two, is which end you start cutting for the top.

This still picture from the video shows the cut lines.

With the 2″ side up, score at 1/2″ on both sides.  With the 6 3/4″ side up, score at 1/2″, 1 7/8″, 3 3/8″, 4 3/4″ and 6 1/4″.  This will give you a 1/2″ tab on each end, and there will be four rectangles that alternate between 1 3/8″ and 1 1/2″ in length.  The end with the shorter rectangle is used for the top of the vertical box, and the end with the longer rectangle is used for the horizontal box.  Then, the side tabs are glued and stuck to the label as shown, and the rest of the strip is glue to form a box inside the two tabs.

Stick label to each side of the bottom panel, then form the sides of the box.

It is hard to explain, but really easy to do.  The video walks you through step-by-step.

Next, fill the box with your treats of choice, then tie a ribbon around the box and either tie a bow or a knot on top.  If I am doing an ornament, after the first half of the bow/knot, I lay a piece of linen thread across the ribbon, and tie the second half of the bow/knot over it.  Then, I tie the two ends of the linen thread together with an overhand knot for the ornament hanger.

There is even a sentiment that can be used on your Thanksgiving table.  If I am standing it up on the table, I would cut off that bottom scallop, so it would stand square on the table.

I hope your enjoyed the project, it would be fun for classmates or co-workers, and most likely you have many scraps around that you could use up in the process.  If you don’t have the Everyday Label punch, the Lots of Labels framelits have a similar sized shape that would work as well.

Until we meet again, I hope your days are blessed.  ~Darby

  • Supplies by Stampin’ Up! unless otherwise noted
  • Card stock: various, whisper white, soft sky, cherry cobbler, early espresso, old olive, emerald envy.
  • Ribbons: old olive mini-chevron, night of navy crinkled ribbon, pear pizazz shimmer ribbon, burlap ribbon, garden green satin ribbon, lemon-lime twist finely woven ribbon.
  • Stamps: Merry Labels, Labels to Love
  • Punch:  Everyday Label punch
  • Inks: cherry cobbler, emerald envy, real red, garden green, lemon-lime twist, berry burst, night of navy, old olive, daffodil delight, always artichoke, pumpkin pie

 

 

 

Quick Cat Treat Holder for Mini-Ghirardelli squares

Hi Everyone,

I thought my All Hallow’s Eve projects were done, but then these cute and quick little Cat Treat Holders showed up in my craft room.  I just had to share them!

Scroll down for the video tutorial.

Each one holds a mini-Ghirardelli chocolate, and is very quick to make.

I used a piece of card stock 1 1/2″ by 7 3/4″, and score with the long side up at 3 3/4″ and 4″.  Then, holding the ends together, placed the open ends at the 1 1/2″ mark on the Envelope Punch Board, and punched.  I flipped him over, and punch the opposite side at the same 1 1/2″ mark.  Then, still holding the open ends together, slid them directly into the throat of the punch, trying to center the curve of the punch on the 1 1/2″ ends of card-stock, and that makes his ears.  If I am being as clear as mud, there is a video that is easier to follow.

Continue reading “Quick Cat Treat Holder for Mini-Ghirardelli squares”

A Shorter Wooden Pumpkin Crate

Hi Everyone,

I love little boxes, bags and treat holders, in fact that is what I make the most.  So, when Stampin’ Up! came out with their little wood crates framelits, I put them right on my shopping list.  What a fun way to gift little treats and gifts, and it is quite easy to create many different versions of the adorable little crate.

Because I wanted to gift one Eos lip balm, I shortened the crate to  fit my purposes.  But, you can shorten it to any length you need following the same steps.  So, it looks more like a milk crate than a vegetable crate.

Here they are, the shorter, and cuter, versions of the crate.

 

Scroll down for a link to the video.

Continue reading “A Shorter Wooden Pumpkin Crate”